User Tools

  • (equal to forum credentials)

Site Tools


repos

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

repos [2014/06/13 21:38]
cmb Added headline for Staging. Corrected some punctuation.
repos [2017/12/19 20:32] (current)
Nachteule [Stable]
Line 1: Line 1:
-**XBian Repositories**+===== XBian Repositories ​=====
  
-Your XBian repos should usually be managed properly with the xbian-config update tool, but you may occasionally need to check, verify or change them manually in /​etc/​apt/​sources.list,​ particularly if moving to staging or devel.+Your XBian repos should usually be managed properly with the xbian-config update tool, but you may occasionally need to check, verify or change them manually in "/​etc/​apt/​sources.list" and "/​etc/​apt/​sources.list.d/​xbian.list" ​, particularly if moving to staging or devel.\\ 
 + 
 +{{wiki:​xbian-config-repos-640.png}} 
 + 
 +If your running latest Debian Stretch, the file "/​etc/​apt/​sources.list"​ should only contain below: 
 + 
 +<​code>​ 
 +deb http://​mirrordirector.raspbian.org/​raspbian/​ stretch main non-free 
 +</​code>​ 
 +for Raspbian based Systems (Raspberry Pi 1, Raspberry Pi Zero, Raspberry Pi Zero W), or 
 + 
 +<​code>​ 
 +deb http://​deb.debian.org/​debian stretch main non-free 
 +</​code>​ 
 +for all others.
  
 ==== Stable ==== ==== Stable ====
-Stable is the currently supported stable build of XBian, although at this writing it is still considered a release candidate. To run stable (which you are running by default on first install) your sources.list file should look like below.+Stable is the currently supported stable build of XBian, although at this writing it is still considered a release candidate. To run stable (which you are running by default on first install) your ** /etc/apt/sources.list.d/​xbian.list ** file should look like below.
  
 +Raspberry Pi 1, Raspberry Pi Zero and Raspberry Pi Zero W:
 <​code>​ <​code>​
-xbian@xbian ~ $ cat /​etc/​apt/​sources.list +deb http://apt.xbian.org/      ​stable  ​main rpi-stretch ​   ​rpi-stretch ​   armv6l-stretch 
-deb http://mirrordirector.raspbian.org/raspbian/ wheezy ​main contrib non-free rpi +### deb http://apt.xbian.org/  staging ​main rpi-stretch ​   rpi-stretch ​   armv6l-stretch 
-deb http://xbian.brantje.com stable ​main +### deb http://apt.xbian.org/  ​devel ​  main rpi-stretch ​   ​rpi-stretch ​   armv6l-stretch
-#deb-src http://mirrordirector.raspbian.org/raspbian/ wheezy ​main contrib non-free rpi+
 </​code>​ </​code>​
  
-The last line is not necessary (as it is commented anyway) but is there by default. 
  
-==== Staging ​==== +Raspberry Pi 2 and Raspberry Pi 3: 
-Staging is the build that contains near-stable packages which are close to being moved into stableTo switch to using staging, your sources.list file should look like below (note you should run sudo apt-get clean and sudo apt-get update after changing your sources list).+<​code>​ 
 +deb http://apt.xbian.org/      stable ​ main rpi2-stretch ​   rpi2-stretch ​   armv7l-stretch 
 +### deb http://apt.xbian.org/ ​ staging main rpi2-stretch ​   rpi2-stretch ​   armv7l-stretch 
 +### deb http://apt.xbian.org/ ​ devel   main rpi2-stretch ​   rpi2-stretch ​   armv7l-stretch 
 +</​code>​
  
 +
 +Cubox-i and Hummingboard:​
 <​code>​ <​code>​
-xbian@xbian ~ $ cat /​etc/​apt/​sources.list +deb http://apt.xbian.org/      stable ​ main imx6-stretch ​   imx6-stretch ​   armv7l-stretch 
-deb http://mirrordirector.raspbian.org/raspbianwheezy ​main contrib non-free rpi +### deb http://apt.xbian.org/  staging main imx6-stretch ​   imx6-stretch ​   armv7l-stretch 
-deb http://​xbian.brantje.com stable main +### deb http://​apt.xbian.org/ ​ devel   main imx6-stretch ​   imx6-stretch ​   armv7l-stretch 
-#deb-src http://mirrordirector.raspbian.org/raspbianwheezy ​main contrib non-free rpi +</​code>​ 
-deb http://​xbian.brantje.com staging main+ 
 + 
 +==== Staging ==== 
 +Staging is the build that contains near-stable packages which are close to being moved into stable. To switch to using staging, your "/​etc/​apt/​sources.list.d/​xbian.list"​ file should look like below (note you should run sudo apt-get clean and sudo apt-get update after changing your sources list). 
 + 
 +Raspberry Pi 1, Raspberry Pi Zero and Raspberry Pi Zero W: 
 +<​code>​ 
 +deb http://apt.xbian.org/      ​stable ​ main rpi-stretch ​   rpi-stretch ​   armv6l-stretch 
 +deb http://​apt.xbian.org/ ​     staging ​main rpi-stretch ​   ​rpi-stretch ​   armv6l-stretch 
 +### deb http://apt.xbian.org/  devel   main rpi-stretch ​   rpi-stretch ​   armv6l-stretch 
 +</​code>​ 
 + 
 + 
 +Raspberry Pi 2 and Raspberry Pi 3: 
 +<​code>​ 
 +deb http://apt.xbian.org/ ​     ​stable ​ main rpi2-stretch ​   rpi2-stretch ​   armv7l-stretch 
 +deb http://apt.xbian.org/      ​staging main rpi2-stretch ​   rpi2-stretch ​   armv7l-stretch 
 +### deb http://​apt.xbian.org/ ​ devel   main rpi2-stretch ​   rpi2-stretch ​   armv7l-stretch 
 +</​code>​ 
 + 
 + 
 +Cubox-i and Hummingboard:​ 
 +<​code>​ 
 +deb http://apt.xbian.org/      stable ​ main imx6-stretch ​   imx6-stretch ​   armv7l-stretch 
 +deb http://apt.xbian.org/ ​     ​staging main imx6-stretch ​   imx6-stretch ​   armv7l-stretch 
 +### deb http://​apt.xbian.org/ ​ devel   main imx6-stretch ​   imx6-stretch ​   armv7l-stretch
 </​code>​ </​code>​
  
 ==== Development ==== ==== Development ====
-Devel is the build used for testing and debugging new packages; you should have no expectation of stability if using this build (however it often may work just fine). You should only use this build if you plan to assist the developers with debugging for future enhancements (or are just very brave). Note you must have the staging repo added as well if you want to run devel. To switch to using devel, your sources.list file should look like below.+Devel is the build used for testing and debugging new packages; you should have no expectation of stability if using this build (however it often may work just fine). You should only use this build if you plan to assist the developers with debugging for future enhancements (or are just very brave). Note you must have the staging repo added as well if you want to run devel. To switch to using devel, your "/​etc/​apt/​sources.list.d/​xbian.list" ​file should look like below.
  
 +Raspberry Pi 1, Raspberry Pi Zero and Raspberry Pi Zero W:
 <​code>​ <​code>​
-xbian@xbian ~ $ cat /​etc/​apt/​sources.list +deb http://apt.xbian.org/  ​stable  ​main rpi-stretch ​   ​rpi-stretch ​   armv6l-stretch 
-deb http://mirrordirector.raspbian.org/raspbian/ wheezy ​main contrib non-free rpi +deb http://apt.xbian.org/ ​ ​staging ​main rpi-stretch ​   ​rpi-stretch ​   armv6l-stretch 
-deb http://​xbian.brantje.com stable main +deb http://apt.xbian.org devel   ​main rpi-stretch ​   rpi-stretch ​   armv6l-stretch
-#deb-src http://​mirrordirector.raspbian.org/raspbian/ wheezy ​main contrib non-free rpi +
-deb http://​xbian.brantje.com staging main +
-deb http://​xbian.brantje.com ​devel main+
 </​code>​ </​code>​
 +
 +
 +Raspberry Pi 2 and Raspberry Pi 3:
 +<​code>​
 +deb http://​apt.xbian.org/ ​ stable ​ main rpi2-stretch ​   rpi2-stretch ​   armv7l-stretch
 +deb http://​apt.xbian.org/ ​ staging main rpi2-stretch ​   rpi2-stretch ​   armv7l-stretch
 +deb http://​apt.xbian.org/ ​ devel   main rpi2-stretch ​   rpi2-stretch ​   armv7l-stretch
 +</​code>​
 +
 +
 +Cubox-i and Hummingboard:​
 +<​code>​
 +deb http://​apt.xbian.org/ ​ stable ​ main imx6-stretch ​   imx6-stretch ​   armv7l-stretch
 +deb http://​apt.xbian.org/ ​ staging main imx6-stretch ​   imx6-stretch ​   armv7l-stretch
 +deb http://​apt.xbian.org/ ​ devel   main imx6-stretch ​   imx6-stretch ​   armv7l-stretch
 +</​code>​
 +
repos.1402688320.txt.gz · Last modified: 2014/06/13 21:38 by cmb