User Tools
- Login (equal to forum credentials)
usb_wifi_dongles
Differences
This shows you the differences between two versions of the page.
|
usb_wifi_dongles [2015/06/09 10:02] deHakkelaar |
usb_wifi_dongles [2015/06/10 17:14] (current) deHakkelaar |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| **USB WiFi dongles** | **USB WiFi dongles** | ||
| - | All below BASH commands needs to be executed as user 'root'.\\ | + | Most all below BASH commands needs to be executed as user 'root'.\\ |
| Best practice if troubleshooting/installing WiFi is to login via SSH using the wired interface 'eth0'. | Best practice if troubleshooting/installing WiFi is to login via SSH using the wired interface 'eth0'. | ||
| Line 9: | Line 9: | ||
| To check WiFi status: | To check WiFi status: | ||
| <code>iwconfig</code> | <code>iwconfig</code> | ||
| + | |||
| + | If your WiFi dongle is designated as 'wlan1' and you want to change to 'wlan0', if not conflicting with other interfaces, you can alter in below file if exists: | ||
| + | <code>nano /etc/udev/rules.d/70-persistent-net.rules | ||
| + | reboot</code> | ||
| Sometimes the WiFi connection cant be established quick enough on boot and you run into troubles if using a shared MySQL database for Kodi/XBMC.\\ | Sometimes the WiFi connection cant be established quick enough on boot and you run into troubles if using a shared MySQL database for Kodi/XBMC.\\ | ||
| Line 14: | Line 18: | ||
| <code>sed -i "s/start on started mountall/start on started mountall and started networking and net-device-up wlan0/" /etc/init/xbmc-preload.conf</code> | <code>sed -i "s/start on started mountall/start on started mountall and started networking and net-device-up wlan0/" /etc/init/xbmc-preload.conf</code> | ||
| - | If your WiFi dongle is designated as 'wlan1' and you want to change to 'wlan0', if not conflicting with other interfaces, you can alter in below file if exists: | + | List 'wlan0' driver specific parameters: |
| - | <code>nano /etc/udev/rules.d/70-persistent-net.rules | + | <code>grep '' /sys/module/$(readlink /sys/class/net/wlan0/device/driver/module | xargs -n 1 basename)/parameters/*</code> |
| - | reboot</code> | + | |
| To determine vendor/device id for connected USB devices: | To determine vendor/device id for connected USB devices: | ||
| Line 22: | Line 25: | ||
| **Vendor/device id "0bda:8179"**\\ | **Vendor/device id "0bda:8179"**\\ | ||
| - | Driver is already installed at "/lib/modules/$(uname -r)/kernel/drivers/staging/rtl8188eu/r8188eu.ko".\\ | + | Driver is already installed at //"/lib/modules/$(uname -r)/kernel/drivers/staging/rtl8188eu/r8188eu.ko"//.\\ |
| But needs below firmware blob: | But needs below firmware blob: | ||
| <code>mkdir /lib/firmware/rtlwifi | <code>mkdir /lib/firmware/rtlwifi | ||
| Line 30: | Line 33: | ||
| **Vendor/device id "0df6:0077"**\\ | **Vendor/device id "0df6:0077"**\\ | ||
| - | Firmware blob is already installed at "/lib/firmware/rtlwifi/rtl8192cufw.bin".\\ | + | Firmware blob is already installed at //"/lib/firmware/rtlwifi/rtl8192cufw.bin"//.\\ |
| - | But needs a driver:\\ | + | But needs a driver assigned thats already installed:\\ |
| - | <code>echo 'install 8192cu /sbin/modprobe --ignore-install 8192cu; /bin/echo "0df6 0077" >| /sys/bus/usb/drivers/rtl8192cu/new_id' | sudo tee /etc/modprobe.d/8192cu.conf | + | <code>echo 'install 8192cu /sbin/modprobe --ignore-install 8192cu; /bin/echo "0df6 0077" >| /sys/bus/usb/drivers/rtl8192cu/new_id' | tee /etc/modprobe.d/8192cu.conf |
| echo "options 8192cu rtw_power_mgnt=0 rtw_enusbss=0" >> /etc/modprobe.d/8192cu.conf | echo "options 8192cu rtw_power_mgnt=0 rtw_enusbss=0" >> /etc/modprobe.d/8192cu.conf | ||
| echo "8192cu" >> /etc/modules | echo "8192cu" >> /etc/modules | ||
| reboot</code> | reboot</code> | ||
usb_wifi_dongles.1433836963.txt.gz · Last modified: 2015/06/09 10:02 by deHakkelaar
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 3.0 Unported
